Electron Microscopy Embedding Media
Electron Microscopy Embedding Media
Electron Microscopy Sciences Light Yellow Melamine Thermosetting Hot Mount Resin 1 KG
Light yellow melamine with mineral and glass filler, thermosetting. For soft to medium hard materials. Excellent edge retention.
Electron Microscopy Sciences PolarStat™ Polarstat Embedding Medium 4 OZ
An aqueous-based frozen section embedding medium designed to support tissue blocks in cryostat sectioning. Formulated to promote rapid freezing, enhanced sectioning and consistent results at a working temperature of -20 degree C.
Electron Microscopy Sciences Kwik-Gard Sylgard™ Refill 2 cartridges and 10 dispensing tips
The Kwik-Gard is specially packaged Sylgard184 silicone that offers a quicker and easier way to apply the silicone, eliminating the messy procedure of preparing the mixture before application. Its special cartridge controls the precise mixing ratio to ensure proper curing. The disposable tip mixes resin and hardener as they are dispensed. Since no air is introduced during mixing, the resin does not need degassing for most applications. The mixed silicone is applied directly to the site, reducing preparation time and material waste.
Each Kwik-Gard cartridge contains 37 mL of resin and hardener. The dispensing tip has a dead volume of 0.75 mL. Curing time for this silicone is 24hrs@25 degree C, 15 min.@150 degree C. 2 cartridges of resin/hardener, 10 tips.
Electron Microscopy Sciences Sylgard™ 184
Same as the Kwik Gard but in its original container. A two-part silicone elastomer, ideal for potting and encapsulating applications. Very low dielectric constant sealing compound used in patch clamping and many other lab applications. After cure, will withstand -55 degree to 200 degree C. Curing time for this silicone 24hrs@25 degree C, and 15 min.@150 degree C.
Crescent Chemical Co Inc D.E.R. 736 PRACT.
D.E.R. 736 pract. Shorter chain than D.E.R. 732, lower viscosity, gives less flexible blocks. Epoxy equivalent weight 175 - 205; viscosity 0.03 - 0.06 Pas at 25 C.Used in electron microscopy. Size - 100ML Storage Conditions - +15 C TO +30 C
Sigma Aldrich Fine Chemicals Biosciences D.E.R.(TM) 332 used as embedding medium | 1675-54-3 | MFCD00080480 | 250G
D.E.R.(TM) 332 used as embedding medium | Mol Wt: 340.41 | 1675-54-3 | MFCD00080480 | 250G
Electron Microscopy Sciences Kwik-Gard Sylgard™ Dispenser
The Kwik-Gard is specially packaged Sylgard184 silicone that offers a quicker and easier way to apply the silicone, eliminating the messy procedure of preparing the mixture before application. Its special cartridge controls the precise mixing ratio to ensure proper curing. The disposable tip mixes resin and hardener as they are dispensed. Since no air is introduced during mixing, the resin does not need degassing for most applications. The mixed silicone is applied directly to the site, reducing preparation time and material waste.
Each Kwik-Gard cartridge contains 37 mL of resin and hardener. The dispensing tip has a dead volume of 0.75 mL. Curing time for this silicone is 24hrs@25 degree C, 15 min.@150 degree C.
Electron Microscopy Sciences Black Bakelite Thermosetting Hot Mount Resin 1 KG
Black bakelite with carbon filler, thermosetting. SEM examination.
Electron Microscopy Sciences Kwik-Gard Sylgard™ Start Up kit
The Kwik-Gard is specially packaged Sylgard184 silicone that offers a quicker and easier way to apply the silicone, eliminating the messy procedure of preparing the mixture before application. Its special cartridge controls the precise mixing ratio to ensure proper curing. The disposable tip mixes resin and hardener as they are dispensed. Since no air is introduced during mixing, the resin does not need degassing for most applications. The mixed silicone is applied directly to the site, reducing preparation time and material waste.
Each Kwik-Gard cartridge contains 37 mL of resin and hardener. The dispensing tip has a dead volume of 0.75 mL. Curing time for this silicone is 24hrs@25 degree C, 15 min.@150 degree C. Dispenser, 1 Cartridge of resin/hardener, 5 tips.
Electron Microscopy Sciences Flat Embedding Crystal
Observing the ultrastructure of cells under an electron microscope is an important aspect of biological research, especially in the neurosciences. These embedding crystals were designed to simplify the preparation of samples and make the process more time efficient.
Electron Microscopy Sciences Red bakelite Thermosetting Hot Mount Resin 1 KG
Red bakelite with wood filler, thermosetting. Routine examination of soft to medium hard materials. Suitable as backing.
PATHOLOGY INNOVATIONS The 18mm Well Bar has four wells that are 3mm deep on one-inch thick stainless steel. These bars are stored in the cryostat and serve as a powerful heat sink to rapidly freeze the block.
When using the Peters Precision Cryoembedding System, embedding is performed in wells machined into the face of one-inch thick stainless steel bars offered in various sizes. The 18mm Well Bar has four wells that are 3mm deep on one-inch thick stainless steel. These bars are stored in the cryostat and serve as a powerful heat sink to rapidly freeze the block. Add additional well bars like this one to your existing Peters Precision Cryoembedding System. The Peters Precision Cryoembedding System was designed by inventor, professor and author of frozen section literature Dr. Stephen Peters to give users more precision and control when doing a high volume of frozen section procedures. Learn how to use the system as well as advanced frozen section technique at pathologyinnovations.com.
Electron Microscopy Sciences Black Epoxy Thermosetting Hot Mount Resin 1 KG
Black epoxy with mineral filler, thermosetting. For hard materials. Excellent edge retention.
Electron Microscopy Sciences Black Bakelite Thermosetting Hot Mount Resin 1 KG
Black bakelite with wood filler, thermosetting. Routine examination of soft to medium hard materials. Suitable as backing.
Electron Microscopy Sciences Kwik-Gard Sylgard™ Dispensing tips
The Kwik-Gard is specially packaged Sylgard184 silicone that offers a quicker and easier way to apply the silicone, eliminating the messy procedure of preparing the mixture before application. Its special cartridge controls the precise mixing ratio to ensure proper curing. The disposable tip mixes resin and hardener as they are dispensed. Since no air is introduced during mixing, the resin does not need degassing for most applications. The mixed silicone is applied directly to the site, reducing preparation time and material waste.
Each Kwik-Gard cartridge contains 37 mL of resin and hardener. The dispensing tip has a dead volume of 0.75 mL. Curing time for this silicone is 24hrs@25 degree C, 15 min.@150 degree C. Tip has dead volume of 0.75 mL.
- 1
- 2